View Poll Results: Which Mod would you Like to See Added
2.5 Inch King Bump Front and Rear
0
0%
Voters: 15. You may not vote on this poll
Jeep JK Punisher Edition Build Log Full Custom Jeep by Del Rey Customs
09-21-2014, 05:14 PM
#1581
JK Enthusiast
Join Date: Apr 2013
Location: Baltimore, md
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
09-22-2014, 04:40 PM
#1583
JK Enthusiast
Join Date: Jan 2013
Location: New York
Posts: 147
Likes: 0
Received 0 Likes
on
0 Posts
09-22-2014, 06:20 PM
#1584
Well. Close. One is about a half inch higher on one side than the other. Details, details, details...it is what makes a build great or a fail.
What is sad is every detail that is lost to rookie mistakes is easily preventable with a little planning and experience. Just a couple pieces of masking tape following the side vents "lines" could have made them PERFECT. Kinda like using the correct crimpers and proper size spade terminals (at worst) or solder/heat shrinking (best). Just a BAD ASS concept of a vehicle, again, completely over the heads of those responsible for building it.
Cough<<<<Jeep Experts>>>>cough cough. Haha.
What is sad is every detail that is lost to rookie mistakes is easily preventable with a little planning and experience. Just a couple pieces of masking tape following the side vents "lines" could have made them PERFECT. Kinda like using the correct crimpers and proper size spade terminals (at worst) or solder/heat shrinking (best). Just a BAD ASS concept of a vehicle, again, completely over the heads of those responsible for building it.
Cough<<<<Jeep Experts>>>>cough cough. Haha.
Last edited by Collyn; 09-22-2014 at 06:29 PM.
09-23-2014, 04:22 AM
#1585
JK Enthusiast
Join Date: Jul 2012
Location: DeBary, FL
Posts: 382
Likes: 0
Received 0 Likes
on
0 Posts
09-23-2014, 04:38 AM
#1586
JK Junkie
I thought it might have been because that's where the indentions were like on the factory fenders (it's off if you like at your stock stuff) but after researching there are no indentions on the smittybilt fenders so yep just poor execution again.
09-23-2014, 05:37 AM
#1587
JK Newbie
Join Date: Jul 2014
Location: Midland, Texas
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Driver side looks crooked as well. They still didn't fit the diamond plate to the box and the crimps are terrible.
I though SEMA had a standard....hell if this is what the latest quality designs in the automotive industry are, I'm in the wrong business. I remember when SEMA vehicles meant something. What a sad joke.
I though SEMA had a standard....hell if this is what the latest quality designs in the automotive industry are, I'm in the wrong business. I remember when SEMA vehicles meant something. What a sad joke.
09-23-2014, 02:01 PM
#1588
this thread is amazing.. I can't get past the crimps and the awful looking floormat things that are screwed down?!?! what happens when water and crap gets between them and the floor boards? rust party?
09-23-2014, 02:18 PM
#1589
JK Junkie
Bed lined floor. Shouldn't be an issue. Maybe. Unless the diamond plate rusts.
09-23-2014, 02:55 PM
#1590
Former Vendor
Thread Starter
Join Date: Feb 2014
Location: United States
Posts: 519
Likes: 0
Received 0 Likes
on
0 Posts