JK-Forum.com - The top destination for Jeep JK and JL Wrangler news, rumors, and discussion - Search Results

Notices
Search: Posts Made By: jeepmojo
Showing results 1 to 15 of 15
Search took 0.01 seconds.
05-19-2019, 12:38 PM
Replies: 48,457
Views: 7,679,125
Posted By akpostal

A little late but if you put the vent on the...

A little late but if you put the vent on the opposite corner of the tap you can also mount the can vertically with the cap pointing down. I dont have the side mount on but you can see the vent...
Forum: Stock JK Tech
02-27-2019, 06:13 PM
Replies: 4
Views: 373
Posted By rob_engineer

I don't know how much fluid is stored in the...

I don't know how much fluid is stored in the system. What I did was this: when changing all four brakes, I compressed all the clipper pistons as far as they would go. I then siphoned as much fluid...
Forum: JK Talk
04-17-2018, 06:32 AM
Replies: 4
Views: 685
Posted By TheDirtman

It cost me around a grand to do it myself when I...

It cost me around a grand to do it myself when I replaced mine. The glass was cheap $125 and the frame was the biggest part of the cost. I had the paint already and shop just charged me $100 to paint...
Forum: JK Talk
04-17-2018, 05:00 AM
Replies: 4
Views: 685
Posted By Rednroll

Replacement of the windshield frame and gasket...

Replacement of the windshield frame and gasket would be best, but I'm sure a good body shop could pound that back into shape and repair it. It will be in your best interest to get it replaced or...
04-16-2018, 03:35 PM
Replies: 2,178
Views: 663,133
Posted By jscherb

Wow, sorry for the damage to your Jeep! Glad the...

Wow, sorry for the damage to your Jeep! Glad the MORryde side mount help up.
Forum: JK Talk
04-16-2018, 02:42 PM
Replies: 4
Views: 685
Posted By karls10jk

Car-part.com and search for a windshield frame....

Car-part.com and search for a windshield frame. You should be able to buy the whole piece including a subscriber'windshield. You'll just follow the directions for dropping the windshield (see...
04-10-2018, 01:13 PM
Replies: 2,178
Views: 663,133
Posted By jscherb

Nicely done!

Nicely done!
04-09-2018, 02:59 PM
Replies: 2,178
Views: 663,133
Posted By jscherb

The edge of the neck should be smooth, so you...

The edge of the neck should be smooth, so you could try smoothing it.
04-09-2018, 10:11 AM
Replies: 48,457
Views: 7,679,125
Posted By Jahamm88

This is Not done on a stock vehicle, I'm at...

This is Not done on a stock vehicle, I'm at somewhere between 2.5-3" lift depending on my load
When lifted, the roll center isn't adjusted when the axle is centered by an adjustable trac bar. It...
04-07-2018, 07:03 AM
Replies: 2,178
Views: 663,133
Posted By akpostal

Dont forget to vent if you add a spigot.

Dont forget to vent if you add a spigot.
04-06-2018, 05:38 PM
Replies: 2,178
Views: 663,133
Posted By akpostal

I had a rotopac mounted under my table for a...

I had a rotopac mounted under my table for a while it was handy there. Ive got the side plates to mount on the front fenders too. If you didnt have the antenna mount Ild say put it behind the tire on...
04-06-2018, 02:36 PM
Replies: 2,178
Views: 663,133
Posted By jscherb

Or on a swing-down overhead panel ;) ...

Or on a swing-down overhead panel ;)

https://www.youtube.com/edit?o=U&video_id=S2b0b3DvurE

In the video above a Rotopax is on the panel but I've got the same panel in my LJ and I mounted a...
04-03-2018, 04:02 PM
Replies: 2,178
Views: 663,133
Posted By jscherb

The company hasn't given me anything more...

The company hasn't given me anything more specific about a date for the steps except "soon after the hinges are released." Hinge release is supposed to be any day now. The steps are designed...
04-03-2018, 03:36 AM
Replies: 2,178
Views: 663,133
Posted By jscherb

JK door hinge bolts are 8mm x 1.25 pitch...

JK door hinge bolts are 8mm x 1.25 pitch (standard thread).
04-02-2018, 03:11 PM
Replies: 2,178
Views: 663,133
Posted By jscherb

So far the only hinge-mounted accessories I've...

So far the only hinge-mounted accessories I've turned over to the company are the folding steps and the HiLift mount. I don't know if there would be enough demand for a Rubican/Rotopax hinge mount,...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands