Oil addative to address dry start knock?
#1
JK Enthusiast
Thread Starter
Join Date: Jul 2011
Location: El Paso TX
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
Oil addative to address dry start knock?
Ran into mechanic friend the other morning, asked him if knew of anything that would address the dry start issue, he said "investigate an oil additive that would allow a good residual coating of the moving parts, Lucas oil may have something that would help".
Anyone try this?
Colder temps here, (5-21 degrees) and the knock is greatly increased.
Currently running Penzoil syn 5w30, Fram xtra guard, (hoping the more expensive Fram would help as the NAPA Gold seems to)
Anyone try this?
Colder temps here, (5-21 degrees) and the knock is greatly increased.
Currently running Penzoil syn 5w30, Fram xtra guard, (hoping the more expensive Fram would help as the NAPA Gold seems to)
#2
It was my understanding that the tapping noise we hear at start up comes from the hydraulic lifters. When it's cold out, the oil thickens and doesn't reach them as quickly thus you get the momentary noise. Also, this is not truly a "dry" start. There will always be a film of oil on all the internal surfaces at start up, thus although annoying, I don't believe there's any major damage as a result. Search for lifter noise and you will find dozens of engines from various manufacturers suffer from the same thing. If I was living where you're at, which is considerably colder than here in Denver, I'd consider using a 0W-20 oil during Winter. Either that or get a block or pan heater.
IMO, the noise has nothing to do with the filter.
If it truly bothers you, there have been reports on here that MMO (Marvel Mystery Oil) and Lucas Oil Treatments have remedied the noise.
IMO, the noise has nothing to do with the filter.
If it truly bothers you, there have been reports on here that MMO (Marvel Mystery Oil) and Lucas Oil Treatments have remedied the noise.
#3
JK Junkie
Personally I would never put any type of additive into my oil.
Many times the dry start noise you are hearing is due to weak anti-drain back valves on some brands of oil filters. Try switching to a WIX filter (also private labeled as Napa Gold and Carquest) and see if that doesn't solve some of your issues.
WIX part numbers:
Air - 49018
Oil - 51348
Many times the dry start noise you are hearing is due to weak anti-drain back valves on some brands of oil filters. Try switching to a WIX filter (also private labeled as Napa Gold and Carquest) and see if that doesn't solve some of your issues.
WIX part numbers:
Air - 49018
Oil - 51348
#4
JK Enthusiast
Join Date: Aug 2011
Location: Lima, ny
Posts: 436
Likes: 0
Received 0 Likes
on
0 Posts
When it really cold, I hold the gas pedal to the floor and crank the engine for a few moments...stop cranking release the pedal and start it normally.
The computer won't let the Jeep start if the gas is held wide open so by cranking and not firing will get some of that oil up top before the engine starts. Every time I do this I don't get a dry start knock...not the best solution but still better then dry starting.
The computer won't let the Jeep start if the gas is held wide open so by cranking and not firing will get some of that oil up top before the engine starts. Every time I do this I don't get a dry start knock...not the best solution but still better then dry starting.
#5
JK Enthusiast
Join Date: Jun 2009
Location: Calgary,AB
Posts: 374
Likes: 0
Received 0 Likes
on
0 Posts
I've tried all the oil filters that I could find up here in Canada, and I still have this dry start noise as well. I got 1 winter out of the motor before it spun the main bearings. I've found that if you plug the block heater in it will not have a dry start up noise, or not that I hear. I've run synthetic oil in the first block but that did not help me out.
If you hold the pedal as previously stated it will not start as it thinks it's flooded. But it will still make the knocking noise when it starts up. Or at least mine does.
I've just gotten used to plugging the jeep in when I'm getting closer to the 0C (32F). But I've found that if you start it more frequently (2-4 hrs) it does not seem to knock on those start ups. It's like it needs to be warm for the clearance inside to be right. I'm thinking that there will be a hemi under my hood when this eng craps out again.
Good luck with the noise and keep it plugged in
If you hold the pedal as previously stated it will not start as it thinks it's flooded. But it will still make the knocking noise when it starts up. Or at least mine does.
I've just gotten used to plugging the jeep in when I'm getting closer to the 0C (32F). But I've found that if you start it more frequently (2-4 hrs) it does not seem to knock on those start ups. It's like it needs to be warm for the clearance inside to be right. I'm thinking that there will be a hemi under my hood when this eng craps out again.
Good luck with the noise and keep it plugged in
#7
JK Freak
Join Date: Jul 2007
Location: eastern north carolina
Posts: 681
Likes: 0
Received 0 Likes
on
0 Posts
Didnt use there additive, but I did change my oil with lucas oil and it took the "knock" away, now changed back to castrol and knock is back, just saying you may want to try it, I plan on buying one quart to try it, hell what 10 dollars to the thousands we have put into our jeeps.
Trending Topics
#8
JK Super Freak
I wonder what the difference is between putting in an additive or just using a heavier 5 or 10W-30 oil?
Don't both just increase viscosity and in effect, give more cushion between parts?
The oil cap on my motor calls for 0W-40. I run 15W-50 in the summer heat, and 5W-40 in the winter.
I don't think the problem is only oil filter drainback, because I am no fan of the piss thin oil they use to squeeze another HP or mpg out of these new engines. Damn stuffs probably too thin for most drainback valves to hold, and too thin to not all drain off the upper engine after shutdown.
I used to run 20W-50 in most of the old hopped up V=8's. They never made a bunch of racket on startup.
I may not be right, but it has always worked for me.
Don't both just increase viscosity and in effect, give more cushion between parts?
The oil cap on my motor calls for 0W-40. I run 15W-50 in the summer heat, and 5W-40 in the winter.
I don't think the problem is only oil filter drainback, because I am no fan of the piss thin oil they use to squeeze another HP or mpg out of these new engines. Damn stuffs probably too thin for most drainback valves to hold, and too thin to not all drain off the upper engine after shutdown.
I used to run 20W-50 in most of the old hopped up V=8's. They never made a bunch of racket on startup.
I may not be right, but it has always worked for me.
Last edited by Yankee; 12-13-2011 at 10:57 AM.
#10
JK Enthusiast
Join Date: Aug 2011
Location: Hawthorne, NV
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
I am running Castrol Edge now and hardly any noise. Last night was 17F Next oil change will be Royal Purple with Napa Platinum filter.