What was done to your JK this week?
JK Newbie
Joined: Oct 2007
Posts: 98
Likes: 0
From: Enterprise, AL (Southeast, AL)
Added a homemade secure trunk to my JK w/ subwoofer!
I added my KC fog lights & XHD Overrider Hood to my XHD front bumper.
I also built this for $48. Check out my thread in the Write-Ups section:
I also built this for $48. Check out my thread in the Write-Ups section:
JK Newbie
Joined: Mar 2008
Posts: 88
Likes: 0
From: Shawnee, KS
I was tired of some extra wind noise while on the highway. Between the windshield frame and softtop, in the center. I went to Home Depot and bought some automobile and marine weather stripping and ran the width of the softtop. It covers the stitching, and is about a 1/4" from the edge. Problem solved. I also mounted a shovel across my rear rollbar, and tomorrow am going to make a grill insert out of expanded aluminum, as seen in the write-ups.
JK Enthusiast
Joined: May 2007
Posts: 166
Likes: 0
From: Brunswick, Me
I had someone in a F350 back into my Car on Friday, while I was in the Gym. Kind of nice of someone to decide and modify my 6 month old 3,600 mile Jeep for me. If he would have stopped short of hitting metal it would be less of a big deal, but he decided to push his luch backing out instead of pulling forward and taking more of his time to drive off.
JK Super Freak
Joined: Jan 2008
Posts: 1,835
Likes: 0
From: The Deep Dark Woods of Texas!
I put together a Body Lift Manual Shifter Geometry How-To (writeup located in the "writeups section" here) after taking dimensions/measurements and building a coathanger wire mockup of the angles last night after I pulled the center console, boots, etc.
! I have the doors off and windows removed and am enjoying the Texas weather!
JK Freak
Joined: Dec 2007
Posts: 632
Likes: 2
From: Alameda, California
I had someone in a F350 back into my Car on Friday, while I was in the Gym. Kind of nice of someone to decide and modify my 6 month old 3,600 mile Jeep for me. If he would have stopped short of hitting metal it would be less of a big deal, but he decided to push his luch backing out instead of pulling forward and taking more of his time to drive off.
JK Freak
Joined: Jan 2008
Posts: 584
Likes: 1
From: Minnetonka, MN
I just did slush mats, Grill Guards, and Sill Guards.
The console top replacement that was delivered had a broken tab, so maybe in a week or so.
I'm gona run my Ham for the first time mobile this afternoon.
The console top replacement that was delivered had a broken tab, so maybe in a week or so.
I'm gona run my Ham for the first time mobile this afternoon.
JK Jedi Master
Joined: Mar 2007
Posts: 14,800
Likes: 374
From: Midwest City, OK
Put some wrap around a couple extension wires that I needed to complete the Shrockworks mid-width front bumper install. Dressed it up a little. Also, had a Zerk fitting on one of the TF QDs that didn't allow grease to flow. Pulled it off, pushed the little ball in a few times with a nail, then reinstalled. Working fine now.
JK Super Freak
Joined: Jun 2007
Posts: 1,350
Likes: 2
From: North East Kingdom, Vermont
New stickers, then took em out and got them dirty
And then to make the Rubi feel loved, I pulled a Liberty out of a place it should not have tried to go.
Sorry, the first picture is a tad blurry, the road was rough, but the dark blob in the white road is them, and that is as far onto the trail as they got, from there it started to get hairy, they were lucky, another mile in and I don't think I cudda got em.
And then to make the Rubi feel loved, I pulled a Liberty out of a place it should not have tried to go.
Sorry, the first picture is a tad blurry, the road was rough, but the dark blob in the white road is them, and that is as far onto the trail as they got, from there it started to get hairy, they were lucky, another mile in and I don't think I cudda got em.