What was done to your JK this week?
01-22-2014, 02:30 AM
JK Junkie
Stone Wall Mount Bottle Opener | Stone Brewing Co. There is no photo but this is the one in my pic. I live about 10 minutes from the brewery so I picked it up there.
01-22-2014, 10:07 AM
JK Freak
Join Date: May 2012
Location: Winchester, Ca
Posts: 864
Likes: 0
Received 0 Likes
on
0 Posts
Finally received my TF front sway bar quick disconnects from some YAHOO on ebay. Installation was a breeze until it came time to install the link to the lower mounting pin on the axle. What a PITA!!
I greased the bushings and pin as noted. The pin fit so tight into the bushings, it was ridiculous! I had a hard time installing the retaining clip. I had to use a pair of vice grips to compress the bushing enough to slide the clip in. (mind you, the JK was sitting on a flat surface as suggested). Anyone running the TF quick discos and have similar problems??
I greased the bushings and pin as noted. The pin fit so tight into the bushings, it was ridiculous! I had a hard time installing the retaining clip. I had to use a pair of vice grips to compress the bushing enough to slide the clip in. (mind you, the JK was sitting on a flat surface as suggested). Anyone running the TF quick discos and have similar problems??
01-22-2014, 12:39 PM
JK Junkie
Finally received my TF front sway bar quick disconnects from some YAHOO on ebay. Installation was a breeze until it came time to install the link to the lower mounting pin on the axle. What a PITA!! I greased the bushings and pin as noted. The pin fit so tight into the bushings, it was ridiculous! I had a hard time installing the retaining clip. I had to use a pair of vice grips to compress the bushing enough to slide the clip in. (mind you, the JK was sitting on a flat surface as suggested). Anyone running the TF quick discos and have similar problems??
I greased the bushings and pin as noted. The pin fit so tight into the bushings, it was ridiculous! I had a hard time installing the retaining clip. I had to use a pair of vice grips to compress the bushing enough to slide the clip in. (mind you, the JK was sitting on a flat surface as suggested). Anyone running the TF quick discos and have similar problems??
01-22-2014, 01:07 PM
JK Jedi Master
Finally received my TF front sway bar quick disconnects from some YAHOO on ebay. Installation was a breeze until it came time to install the link to the lower mounting pin on the axle. What a PITA!! I greased the bushings and pin as noted. The pin fit so tight into the bushings, it was ridiculous! I had a hard time installing the retaining clip. I had to use a pair of vice grips to compress the bushing enough to slide the clip in. (mind you, the JK was sitting on a flat surface as suggested). Anyone running the TF quick discos and have similar problems??
I greased the bushings and pin as noted. The pin fit so tight into the bushings, it was ridiculous! I had a hard time installing the retaining clip. I had to use a pair of vice grips to compress the bushing enough to slide the clip in. (mind you, the JK was sitting on a flat surface as suggested). Anyone running the TF quick discos and have similar problems??
01-22-2014, 05:30 PM
JK Enthusiast
Box of stuff came in today.
MOPAR Sill Guards
RR Fuel Door Cover
RR Grab Handles
RR Hood Latches
And a back order notice for my RR Quick Release Mirrors.
It'll be in the 20s tomorrow so I guess I won't need them anyway but I wish Quadratec would fix their in stock but actually out of stock issues. Ha gives me something to look for.
MOPAR Sill Guards
RR Fuel Door Cover
RR Grab Handles
RR Hood Latches
And a back order notice for my RR Quick Release Mirrors.
It'll be in the 20s tomorrow so I guess I won't need them anyway but I wish Quadratec would fix their in stock but actually out of stock issues. Ha gives me something to look for.
01-22-2014, 05:36 PM
JK Super Freak
Join Date: Dec 2010
Location: CURRENTLY HAWAII
Posts: 1,177
Likes: 0
Received 0 Likes
on
0 Posts
sent by aliens