What was done to your JK this week?
JK Freak
Joined: Apr 2008
Posts: 737
Likes: 0
From: Nor-Cal
JK Jedi Master
Joined: Nov 2006
Posts: 15,170
Likes: 0
From: .
I am sure if you had the part number you could order it from your local dealer.
JK Enthusiast
Joined: May 2008
Posts: 268
Likes: 0
From: Central Wisconsin
JK Super Freak
Joined: Dec 2007
Posts: 1,750
Likes: 1
From: WV relocated 2 Dyess AFB, TX
Its funny we want the parts we dont have and hate the parts we do. You know if it were switched around as to where we had the euro stuff we would want the american stuff. JEEP = NEVER SATISFIED WITH STOCK.
Funny though that everyone thought the bumpers were aftermarket. Look at the location of the poster, should give you a heads up for asking funny questions.
EDIT: Oh yeah the plates kind of give it away as well.
Funny though that everyone thought the bumpers were aftermarket. Look at the location of the poster, should give you a heads up for asking funny questions.
EDIT: Oh yeah the plates kind of give it away as well.
Last edited by JulietKilo; Jul 27, 2008 at 06:24 PM.
JK Enthusiast
Joined: Jul 2008
Posts: 458
Likes: 0
From: Rohnert Park, CA
Built roof rack for use with bikini top. 
Ordered lift kit.
https://www.jk-forum.com/forums/jk-write-ups-39/budget-roof-rack-49315/
Ordered lift kit.
https://www.jk-forum.com/forums/jk-write-ups-39/budget-roof-rack-49315/
JK Newbie
Joined: Jul 2008
Posts: 89
Likes: 0
From: Orlando, FL
I finally installed my tow hooks. Personally think i did a pretty good job. next step is ordering my hi-lift, winch kit, lift-mate, and some grab handles. Wish I woulda started with all this earlier
JK Super Freak
Joined: May 2008
Posts: 1,279
Likes: 0
From: Grand Junction, CO
Welded on the ORE C2 gussets and the LCA skids/braces. Looks like both mods are well worthwhile. The axles C's are certainly well braced.
Used my New Hobart Handler 210 MIG welder. I did the easy ones but a buddy with 24 years as a commercial welder did the vertical welds. He liked the welder so much he bought one on his way home for his garage. He said it welded better than the big Lincoln MIG machines at his employers.
Used my New Hobart Handler 210 MIG welder. I did the easy ones but a buddy with 24 years as a commercial welder did the vertical welds. He liked the welder so much he bought one on his way home for his garage. He said it welded better than the big Lincoln MIG machines at his employers.
JK Enthusiast
Joined: May 2008
Posts: 268
Likes: 0
From: Central Wisconsin
Welded on the ORE C2 gussets and the LCA skids/braces. Looks like both mods are well worthwhile. The axles C's are certainly well braced.
Used my New Hobart Handler 210 MIG welder. I did the easy ones but a buddy with 24 years as a commercial welder did the vertical welds. He liked the welder so much he bought one on his way home for his garage. He said it welded better than the big Lincoln MIG machines at his employers.
Used my New Hobart Handler 210 MIG welder. I did the easy ones but a buddy with 24 years as a commercial welder did the vertical welds. He liked the welder so much he bought one on his way home for his garage. He said it welded better than the big Lincoln MIG machines at his employers.
Eternal ***erator
Joined: Oct 2006
Posts: 18,270
Likes: 3
From: Niagara, New York
JK Enthusiast
Joined: Apr 2007
Posts: 189
Likes: 0
From: Italy
Our Euro bumpers suck big time! Front eats up a lot of your approach angle and rear has the stinky 'lip' for the license plate hanging down and scrapes on the obstacles !!!
For Happy... those are rear fog lights and reflectors. Not sure 'bout making reverse lights there as they're slightly pointed outwards...
.